Welcome to Shandong Jiyang Machinery Factory(Skyscraper Machinery)!
How to use and maintain a hydraulic loading ramp?
Publish Time:
May 23,2022
The hydraulic dock leveler uses imported seals to ensure good sealing performance of the hydraulic system. It uses an imported integrated modular hydraulic station, which has good sealing performance and a long service life. The high-strength U-beam design ensures that it remains undeformed under high loads for a long time. The anti-slip checkered steel plate provides good anti-slip performance for the platform. Roll-up skirts should be installed on both sides to prevent toes from getting caught in the platform and causing accidental injuries. Support rods are provided to ensure that maintenance personnel can safely access the boarding bridge for maintenance.
Hydraulic Loading Bridge It adopts full hydraulic drive, easy to operate, and reliable operation. Structure: The lip plate is connected to the boarding shaft through a long shaft, with high strength and good reliability.
The hydraulic loading bridge uses imported seals to ensure good sealing performance of the hydraulic system. It uses imported integrated modular hydraulic stations, with good sealing performance and long service life. The design of the high-strength U-shaped beam ensures that it remains undeformed under high loads for a long time. Anti-slip checkered steel plates are used to give the platform good anti-slip performance. Roll-over skirts should be set on both sides to prevent toes from being stuck in the platform and causing accidental injuries. Support rods are provided to ensure that maintenance personnel can enter the boarding bridge for maintenance.
Hydraulic Loading Bridge It has a base and a bridge plate, and the bridge plate is connected to the base through a center pin shaft in the middle.
A front buffer cylinder is provided at the front of the center pin shaft, and a rear buffer cylinder is provided at the rear of the center pin shaft. The two ends of the rear buffer cylinder are hinged to the bridge plate and the base respectively. It can Loading Bridge smoothly change from a tilted state to a horizontal state, or from a horizontal state to a tilted state when lowering the bridge. The structure is simple and does not require power, avoiding impact on heavy vehicles.
You can extend the life of Loading Bridge by performing the following operations:
1. Check the rollers, bearings, and center shaft; lubrication and wear of the top of the cylinder and bearings.
2. Pay attention to adding lubricating oil to extend the service life of the bearings.
3. Check the connection parts of the hydraulic boarding bridge pipeline. If there is any damage, replace the pipeline immediately; provide loose and tight pipe joints at the connection points.
4. Remove the lowering valve, clean it with compressed air, and reinstall the valve core.
5. Remove all the hydraulic oil from the oil tank, open the oil tank, remove the oil filter, clean it, put it back in the oil tank, install it on site, and inject new oil into the oil tank.
6. Do a good job of hydraulic Loading Bridge weather protection. When not in use, keep the idle hydraulic loading bridge indoors or cover it with a cloth. Many companies leave it outdoors after use. Long-term sun exposure and wind will cause rusting of the parts of the hydraulic loading bridge, loosening of the welded structure, and unfavorable to long-term use.
Previous
BLOGS
Liu Tiesheng was re-elected as a member of the Jiyang County CPPCC for five consecutive terms and served two terms as a standing committee member. He is the former chairman of Shandong Jiyang Machinery Factory Co., Ltd. During the transition from a planned economy to a market economy, he demonstrated exceptional foresight and courage, leading the way in technological innovation and contributing to the prosperity of Shandong Province and the nation. His achievements made the company a shining success. He is considered a prominent figure in Jiyang County's 30 years of reform and opening up, a pioneer in the development of the Jiyang lifting platform industry, and a well-deserved leader in the machinery industry!
Introduction to the civil engineering advantages of rail-guided lifting platforms
Guide rail lifting platform is a kind of non-scissor hydraulic lifting mechanical equipment, used for cargo transmission between floors of two or three-story industrial plants, restaurants, and hotels. It can have a low height of 150-300mm, especially suitable for workplaces where pits cannot be excavated, and does not require upper suspension points. It comes in various forms (single-column, double-column, four-column). The equipment operates smoothly. The guide rails of the guide rail lifting platform are generally made of channel steel, I-beams, and square tubes welded together. It is simple, reliable, and economical for cargo transmission. Hydraulic lifting platforms are multifunctional lifting and handling mechanical equipment with lifting heights ranging from 1m to 30m. They can also be customized according to different user needs.
What is the purpose of a guide rail lift platform?
Rail-guided lifting platforms are widely used and are a popular product on the market due to their various advantages. However, there are many points of knowledge that need to be understood when using them, as many users are not aware of them. Next, let me introduce the uses of rail-guided lifting platforms. Those interested can read on.
How to maintain a guide rail lift platform?
The advantages of rail-type lifting platforms lie in the hydraulic system's anti-falling and overload safety protection devices. The railings on each floor and the lifting platform are made of stainless steel. In addition, they feature high load-bearing capacity, high stability, and a long service life. Below are some maintenance methods for rail-type lifting platforms.
What are the advantages of a guide rail lift platform?
The industry of guide rail lifting platforms has a bright future. They offer numerous benefits to businesses, making them highly popular among customers. To help people become more familiar with them, let's discuss the advantages of guide rail lifting platforms. Hopefully, this will be helpful to many.
Dry goods sharing: Understand the functions of a guide rail lift platform in one minute
A rail-guided lifting platform is a hydraulic lifting platform consisting of a hydraulic lifting section, guide rails, and a loading platform. What is the purpose of a rail-guided lifting platform?
Shandong Jiyang Machinery Factory
Tel: 86-531-84211935 86-531-84222430
Fax: 86-531-84211081
Mobile: 86-185-6002-7566
Email: sdjyjxc@126.com
Address: No. 1, Mechanical Industry Park, Jiyang District, Jinan City, Shandong Province (West side of G220 line, Huihe Street)
Mobile Website